WEG 01536AP1DGD215TZ-S Rolled Steel Grain Dryer 10-15 HP 2P 213/5TZ 1Ph 230 V 60 Hz IC410 - TEAO - Foot-mounted Furnace/Air Handler

WEG 01536AP1DGD215TZ-S Rolled Steel Grain Dryer 10-15 HP 2P 213/5TZ 1Ph 230 V 60 Hz IC410 - TEAO - Foot-mounted Furnace/Air HandlerStandard NEMA MG 1 Frequency 60 Hz Voltage 230 V Number of poles 2 Degree of Protection IP55 Synchronous speed 3600 rpm Output rating 10 15 HP Mounting F 3 Flange Without Terminal box Top Enclosure IC410 TEAO Specifications 230 V 60 Hz 2P Electric Motors Frame 213 5TZ Output 15 HP (11 kW) Number of Poles 2 Frequency 60 Hz Rated speed 3510 rpm Slip 2. 50 % Rated voltage 230 V Rated current 55. 5 A L. R. Amperes 438 A LRC 7. 9x(Code H) No load current

1 POLES 2 NUMBER SPEEDS 1 RPM 3560 RPM 2 3560 HERTZ 60 VOLTS PRIMARY 2300/4000 VOLTS 4000 VOLTS 2 2300 FRME 449 SHAFT CODE TS MOUNTING HORZ-FOOTED ASSEMBLY POSITION F1 MOTOR TYPE JC OPPOSITE END BEARING 6315-J/C3 SHAFT END BEARING 6315-J/C3 AMBIENT 40 ROTATION UNI-DIRECTIONAL SERVICE FACTOR 1

55 FULL LOAD AMPS PRIMARY 4

Frame Material Cast Iron Impregnation Method Double impregnation polyester Space Heater Voltage 110-127/200-240 V Main terminal box hole NPT 1" Terminal Block Without Shaft Locking Device Without Drain Rubber

Standard NEMA MG-1 Frequency 60 Hz Voltage 208-230 V Number of poles 2 Synchronous speed 3600 rpm Output rating 5 HP Mounting F-3 Flange Without Terminal box¹ Top Enclosure IC01 - ODP Electric Motors

80 A Rated torque 7

2 POLES 4 NUMBER SPEEDS 1 RPM 1725 HERTZ 60 VOLTS PRIMARY 208-230/460 V VOLTS 208 VOLTS 2 230 VOLTS 3 460 FRME 145 SHAFT CODE TC STACK 4

6 POLES 4 NUMBER SPEEDS 1 RPM 1770 HERTZ 60 VOLTS PRIMARY 200 VOLTS 200 FRME 284 SHAFT CODE TS MOUNTING HORZ-FOOTED ASSEMBLY POSITION F1 MOTOR TYPE UTE OPPOSITE END BEARING 6207-2Z-J/C3 SHAFT END BEARING 6310-2Z-J/C3 AMBIENT 40 ROTATION DUAL SERVICE FACTOR 1

Standard NEMA MG-1 Frequency 60 Hz Voltage 200/400 V Number of poles 2 Synchronous speed 3600 rpm Output rating 5 HP Mounting F-1 Flange C Terminal box¹ Left position Enclosure IC01 - ODP Electric Motors

2 POLES 4 NUMBER SPEEDS 1 RPM 1775 HERTZ 60 VOLTS PRIMARY 200 VOLTS 200 FRME 254 SHAFT CODE T MOUNTING HORZ-FOOTED ASSEMBLY POSITION F1 MOTOR TYPE UTE OPPOSITE END BEARING 6207-2Z-J/C3 SHAFT END BEARING 6309-2Z-J/C3 AMBIENT 40 ROTATION DUAL SERVICE FACTOR 1

80 Technical Data

Model_Number K055MAE0216012B PRODUCT NAME

2 FULL LOAD AMPS PRIMARY 40-36/18 SERVICE FACTOR AMPS PRIMARY 48-42/20